-------------------------------------------------------------------------------- libcamera-apps Bug Report -------------------------------------------------------------------------------- Date: 04-04-2023 (14:21:47) Command: ./arducam-camera-bug-report -------------------------------------------------------------------------------- Hardware information -------------------------------------------------------------------------------- ** hostname ** lanolinfabrik ** uname -r ** 5.15.84-v7l+ ** cat /proc/cpuinfo | tail -n 4 ** Hardware : BCM2711 Revision : c03140 Serial : 1000000086fb061b Model : Raspberry Pi Compute Module 4 Rev 1.0 -------------------------------------------------------------------------------- libcamera verison -------------------------------------------------------------------------------- ** sudo dpkg -l | grep libcamera ** ii libcamera-apps-lite 0~git20230125+9f08463-1 armhf libcamera-apps-lite ii libcamera0:armhf 0~git20230124+9b860a66-1 armhf complex camera support library ii python3-libcamera 0~git20230124+9b860a66-1 armhf complex camera support library (Python 3 bindings) -------------------------------------------------------------------------------- Camera detect -------------------------------------------------------------------------------- ** ls /dev/video* ** /dev/video10 /dev/video11 /dev/video12 /dev/video13 /dev/video14 /dev/video15 /dev/video16 /dev/video18 /dev/video19 /dev/video20 /dev/video21 /dev/video22 /dev/video23 /dev/video31 -------------------------------------------------------------------------------- Configuration -------------------------------------------------------------------------------- ** cat /boot/config.txt ** #SET MODEM APN FOR FRAUNHOFER HHI DEVICE #apn=internet # For more options and information see # http://rpf.io/configtxt # Some settings may impact device functionality. See link above for details # uncomment if you get no picture on HDMI for a default "safe" mode #hdmi_safe=1 # uncomment the following to adjust overscan. Use positive numbers if console # goes off screen, and negative if there is too much border #overscan_left=16 #overscan_right=16 #overscan_top=16 #overscan_bottom=16 # uncomment to force a console size. By default it will be display's size minus # overscan. #framebuffer_width=1280 #framebuffer_height=720 # uncomment if hdmi display is not detected and composite is being output #hdmi_force_hotplug=1 # uncomment to force a specific HDMI mode (this will force VGA) #hdmi_group=1 #hdmi_mode=1 # uncomment to force a HDMI mode rather than DVI. This can make audio work in # DMT (computer monitor) modes #hdmi_drive=2 # uncomment to increase signal to HDMI, if you have interference, blanking, or # no display #config_hdmi_boost=4 # uncomment for composite PAL #sdtv_mode=2 #uncomment to overclock the arm. 700 MHz is the default. #arm_freq=800 # Uncomment some or all of these to enable the optional hardware interfaces #dtparam=i2c_arm=on #dtparam=i2s=on #dtparam=spi=on # Uncomment this to enable infrared communication. #dtoverlay=gpio-ir,gpio_pin=17 #dtoverlay=gpio-ir-tx,gpio_pin=18 # Additional overlays and parameters are documented /boot/overlays/README # Enable audio (loads snd_bcm2835) dtparam=audio=on # Automatically load overlays for detected cameras camera_auto_detect=1 # Automatically load overlays for detected DSI displays display_auto_detect=1 # Enable DRM VC4 V3D driver dtoverlay=vc4-kms-v3d max_framebuffers=2 # Disable compensation for displays with overscan disable_overscan=1 [cm4] # Enable host mode on the 2711 built-in XHCI USB controller. # This line should be removed if the legacy DWC2 controller is required # (e.g. for USB device mode) or if USB support is not required. otg_mode=1 [all] [pi4] # Run as fast as firmware / board allows dtoverlay=vc4-fkms-v3d max_framebuffers=2 [all] #dtoverlay=vc4-fkms-v3d dtoverlay=dwc2,dr_mode=host dtdebug=1 dtoverlay=i2c3,pins_2_3 dtoverlay=uart4 dtoverlay=uart5 enable_uart=1 gpu_mem=128 start_x=1 disable_splash=1 dtoverlay=disable-bt boot_delay=0 ** ls /boot/overlays/* | grep arducam ** /boot/overlays/arducam-64mp.dtbo /boot/overlays/arducam-pivariety.dtbo ** ls /boot/overlays/* | grep imx ** /boot/overlays/imx219.dtbo /boot/overlays/imx258.dtbo /boot/overlays/imx290.dtbo /boot/overlays/imx296.dtbo /boot/overlays/imx327.dtbo /boot/overlays/imx378.dtbo /boot/overlays/imx462.dtbo /boot/overlays/imx477.dtbo /boot/overlays/imx519.dtbo /boot/overlays/imx708.dtbo ** ls /lib/modules/$(uname -r)/kernel/drivers/media/i2c ** ad5398_vcm.ko.xz adv7180.ko.xz arducam_64mp.ko.xz arducam-pivariety.ko.xz cs53l32a.ko.xz cx25840 dw9807-vcm.ko.xz imx219.ko.xz imx258.ko.xz imx290.ko.xz imx296.ko.xz imx477.ko.xz imx519.ko.xz imx708.ko.xz ir-kbd-i2c.ko.xz irs1125.ko.xz msp3400.ko.xz mt9v011.ko.xz ov2311.ko.xz ov5647.ko.xz ov7251.ko.xz ov7640.ko.xz ov9281.ko.xz saa7115.ko.xz sony-btf-mpx.ko.xz tc358743.ko.xz tvp5150.ko.xz tw2804.ko.xz tw9903.ko.xz tw9906.ko.xz uda1342.ko.xz wm8775.ko.xz ** i2cdetect -y -r 10 ** /bin/sh: 1: i2cdetect: not found -------------------------------------------------------------------------------- Memory -------------------------------------------------------------------------------- ** cat /proc/meminfo | grep Cma ** CmaTotal: 327680 kB CmaFree: 321020 kB -------------------------------------------------------------------------------- Cameras -------------------------------------------------------------------------------- ** libcamera-still --list-cameras ** No cameras available! -------------------------------------------------------------------------------- Versions -------------------------------------------------------------------------------- ** uname -a ** Linux lanolinfabrik 5.15.84-v7l+ #1613 SMP Thu Jan 5 12:01:26 GMT 2023 armv7l GNU/Linux ** cat /etc/os-release ** PRETTY_NAME="Raspbian GNU/Linux 11 (bullseye)" NAME="Raspbian GNU/Linux" VERSION_ID="11" VERSION="11 (bullseye)" VERSION_CODENAME=bullseye ID=raspbian ID_LIKE=debian HOME_URL="http://www.raspbian.org/" SUPPORT_URL="http://www.raspbian.org/RaspbianForums" BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs" -------------------------------------------------------------------------------- libcamera-still -n -t 1000 -o arducam-test.jpg --width 1920 --height 1080 -------------------------------------------------------------------------------- [0:08:40.468297347] [1450]  INFO Camera camera_manager.cpp:299 libcamera v0.0.3+40-9b860a66 ERROR: *** no cameras available *** -------------------------------------------------------------------------------- Logs -------------------------------------------------------------------------------- ** ls -lh arducam-test.jpg ** ls: cannot access 'arducam-test.jpg': No such file or directory ** dmesg | grep arducam ** ** dmesg | grep imx ** ** dmesg | grep ov9281 ** ** dmesg ** [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.15.84-v7l+ (dom@buildbot) (arm-linux-gnueabihf-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1613 SMP Thu Jan 5 12:01:26 GMT 2023 [ 0.000000] CPU: ARMv7 Processor [410fd083] revision 3 (ARMv7), cr=30c5383d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Raspberry Pi Compute Module 4 Rev 1.0 [ 0.000000] random: crng init done [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Reserved memory: created CMA memory pool at 0x000000001ac00000, size 320 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000030000000-0x00000000fbffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000037ffffff] [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000fbffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000fbffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s35788 r8192 d21556 u65536 [ 0.000000] pcpu-alloc: s35788 r8192 d21556 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 997696 [ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 smsc95xx.macaddr=DC:A6:32:FE:85:76 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 console=ttyAMA0,115200 console=tty1 root=PARTUUID=029458e5-02 rootfstype=ext4 fsck.repair=yes rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x0000000014890000-0x0000000018890000] (64MB) [ 0.000000] Memory: 3548548K/3997696K available (10240K kernel code, 1386K rwdata, 3308K rodata, 2048K init, 591K bss, 121468K reserved, 327680K cma-reserved, 3211264K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 35518 entries in 105 pages [ 0.000000] ftrace: allocated 105 pages with 4 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] irq_brcmstb_l2: registered L2 intc (/soc/interrupt-controller@7ef00100, parent irq: 25) [ 0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns [ 0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns [ 0.000022] Switching to timer-based delay loop, resolution 18ns [ 0.000383] Console: colour dummy device 80x30 [ 0.001051] printk: console [tty1] enabled [ 0.001132] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000) [ 0.001184] pid_max: default: 32768 minimum: 301 [ 0.001337] LSM: Security Framework initializing [ 0.001548] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.001596] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.003139] cgroup: Disabling memory control group subsystem [ 0.003391] CPU: Testing write buffer coherency: ok [ 0.003461] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003920] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005426] Setting up static identity map for 0x200000 - 0x20003c [ 0.005643] rcu: Hierarchical SRCU implementation. [ 0.006654] smp: Bringing up secondary CPUs ... [ 0.007822] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.009132] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.010463] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.010634] smp: Brought up 1 node, 4 CPUs [ 0.010714] SMP: Total of 4 processors activated (432.00 BogoMIPS). [ 0.010747] CPU: All CPU(s) started in HYP mode. [ 0.010772] CPU: Virtualization extensions available. [ 0.011525] devtmpfs: initialized [ 0.026599] VFP support v0.3: implementor 41 architecture 3 part 40 variant 8 rev 0 [ 0.026848] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.026904] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.036742] pinctrl core: initialized pinctrl subsystem [ 0.037994] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.042490] DMA: preallocated 1024 KiB pool for atomic coherent allocations [ 0.043333] audit: initializing netlink subsys (disabled) [ 0.043604] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1 [ 0.044250] thermal_sys: Registered thermal governor 'step_wise' [ 0.044938] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.044995] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.045407] Serial: AMBA PL011 UART driver [ 0.059905] bcm2835-mbox fe00b880.mailbox: mailbox enabled [ 0.100057] raspberrypi-firmware soc:firmware: Attached to firmware from 2023-01-05T10:47:47, variant start_x [ 0.110074] raspberrypi-firmware soc:firmware: Firmware hash is 8ba17717fbcedd4c3b6d4bce7e50c7af4155cba9 [ 0.170655] Kprobes globally optimized [ 0.176647] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1 [ 0.181316] vgaarb: loaded [ 0.181858] SCSI subsystem initialized [ 0.182104] usbcore: registered new interface driver usbfs [ 0.182181] usbcore: registered new interface driver hub [ 0.182283] usbcore: registered new device driver usb [ 0.182700] usb_phy_generic phy: supply vcc not found, using dummy regulator [ 0.182900] usb_phy_generic phy: dummy supplies not allowed for exclusive requests [ 0.183241] pps_core: LinuxPPS API ver. 1 registered [ 0.183270] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.183318] PTP clock support registered [ 0.184926] clocksource: Switched to clocksource arch_sys_counter [ 0.265687] VFS: Disk quotas dquot_6.6.0 [ 0.265818] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.266021] FS-Cache: Loaded [ 0.266240] CacheFiles: Loaded [ 0.277124] NET: Registered PF_INET protocol family [ 0.277391] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.278987] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.279044] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.279090] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.279175] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.279261] TCP: Hash tables configured (established 8192 bind 8192) [ 0.279428] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.279484] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.279754] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.285826] RPC: Registered named UNIX socket transport module. [ 0.285861] RPC: Registered udp transport module. [ 0.285888] RPC: Registered tcp transport module. [ 0.285914] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.285949] PCI: CLS 0 bytes, default 64 [ 1.338788] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available [ 1.341485] Initialise system trusted keyrings [ 1.341805] workingset: timestamp_bits=14 max_order=20 bucket_order=6 [ 1.350734] zbud: loaded [ 1.352588] FS-Cache: Netfs 'nfs' registered for caching [ 1.353450] NFS: Registering the id_resolver key type [ 1.353499] Key type id_resolver registered [ 1.353526] Key type id_legacy registered [ 1.353689] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.353721] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.354937] Key type asymmetric registered [ 1.354969] Asymmetric key parser 'x509' registered [ 1.355212] bounce: pool size: 64 pages [ 1.355315] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.355563] io scheduler mq-deadline registered [ 1.355595] io scheduler kyber registered [ 1.365043] gpio-507 (ant1): hogged as output/high [ 1.366500] gpio-511 (ant2): hogged as output/low [ 1.368225] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges: [ 1.368283] brcm-pcie fd500000.pcie: No bus range found for /scb/pcie@7d500000, using [bus 00-ff] [ 1.368399] brcm-pcie fd500000.pcie: MEM 0x0600000000..0x063fffffff -> 0x00c0000000 [ 1.368511] brcm-pcie fd500000.pcie: IB MEM 0x0000000000..0x00ffffffff -> 0x0400000000 [ 1.964950] brcm-pcie fd500000.pcie: link down [ 1.975415] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled [ 1.978624] iproc-rng200 fe104000.rng: hwrng registered [ 1.979038] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB) [ 1.980665] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000 [ 1.993639] brd: module loaded [ 2.003992] loop: module loaded [ 2.004817] Loading iSCSI transport class v2.0-870. [ 2.010109] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000 [ 2.105095] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus [ 2.106343] usbcore: registered new interface driver r8152 [ 2.106429] usbcore: registered new interface driver lan78xx [ 2.106505] usbcore: registered new interface driver smsc95xx [ 2.132576] xhci-hcd fe9c0000.xhci: xHCI Host Controller [ 2.132631] xhci-hcd fe9c0000.xhci: new USB bus registered, assigned bus number 1 [ 2.135091] xhci-hcd fe9c0000.xhci: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000000010010 [ 2.135206] xhci-hcd fe9c0000.xhci: irq 77, io mem 0xfe9c0000 [ 2.135505] xhci-hcd fe9c0000.xhci: xHCI Host Controller [ 2.135547] xhci-hcd fe9c0000.xhci: new USB bus registered, assigned bus number 2 [ 2.135592] xhci-hcd fe9c0000.xhci: Host supports USB 3.0 SuperSpeed [ 2.135963] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 [ 2.136006] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.136043] usb usb1: Product: xHCI Host Controller [ 2.136073] usb usb1: Manufacturer: Linux 5.15.84-v7l+ xhci-hcd [ 2.136103] usb usb1: SerialNumber: fe9c0000.xhci [ 2.136813] hub 1-0:1.0: USB hub found [ 2.136896] hub 1-0:1.0: 1 port detected [ 2.137577] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.137886] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15 [ 2.137929] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.137966] usb usb2: Product: xHCI Host Controller [ 2.137995] usb usb2: Manufacturer: Linux 5.15.84-v7l+ xhci-hcd [ 2.138025] usb usb2: SerialNumber: fe9c0000.xhci [ 2.138689] hub 2-0:1.0: USB hub found [ 2.138770] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 2.139316] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) [ 2.139721] dwc_otg: FIQ enabled [ 2.139735] dwc_otg: NAK holdoff enabled [ 2.139748] dwc_otg: FIQ split-transaction FSM enabled [ 2.139766] Module dwc_common_port init [ 2.140207] usbcore: registered new interface driver uas [ 2.140354] usbcore: registered new interface driver usb-storage [ 2.140591] mousedev: PS/2 mouse device common for all mice [ 2.145878] sdhci: Secure Digital Host Controller Interface driver [ 2.145913] sdhci: Copyright(c) Pierre Ossman [ 2.146667] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.150529] ledtrig-cpu: registered to indicate activity on CPUs [ 2.150905] hid: raw HID events driver (C) Jiri Kosina [ 2.151113] usbcore: registered new interface driver usbhid [ 2.151144] usbhid: USB HID core driver [ 2.157528] Initializing XFRM netlink socket [ 2.157603] NET: Registered PF_PACKET protocol family [ 2.157723] Key type dns_resolver registered [ 2.158110] Registering SWP/SWPB emulation handler [ 2.158922] registered taskstats version 1 [ 2.158964] Loading compiled-in X.509 certificates [ 2.159840] Key type .fscrypt registered [ 2.159871] Key type fscrypt-provisioning registered [ 2.172210] uart-pl011 fe201000.serial: there is not valid maps for state default [ 2.172499] uart-pl011 fe201000.serial: cts_event_workaround enabled [ 2.172642] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 34, base_baud = 0) is a PL011 rev2 [ 2.484962] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 2.489825] printk: console [ttyAMA0] enabled [ 2.665848] usb 1-1: New USB device found, idVendor=0424, idProduct=2742, bcdDevice= 2.06 [ 2.669077] fe201800.serial: ttyAMA1 at MMIO 0xfe201800 (irq = 34, base_baud = 0) is a PL011 rev2 [ 2.672088] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.678426] fe201a00.serial: ttyAMA2 at MMIO 0xfe201a00 (irq = 34, base_baud = 0) is a PL011 rev2 [ 2.687523] usb 1-1: Product: USB2742 [ 2.706255] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer [ 2.707646] usb 1-1: Manufacturer: Microchip Tech [ 2.710828] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver [ 3.397854] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0 [ 3.403890] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated [ 3.440104] of_cfs_init [ 3.442667] of_cfs_init: OK [ 3.447930] hub 1-1:1.0: USB hub found [ 3.451784] hub 1-1:1.0: 3 ports detected [ 3.483297] mmc0: SDHCI controller on fe340000.mmc [fe340000.mmc] using ADMA [ 3.512739] Waiting for root device PARTUUID=029458e5-02... [ 3.576197] mmc1: new high speed SDIO card at address 0001 [ 3.597196] mmc0: new ultra high speed DDR50 SDHC card at address aaaa [ 3.604670] mmcblk0: mmc0:aaaa SC16G 14.8 GiB [ 3.616162] mmcblk0: p1 p2 [ 3.619499] mmcblk0: mmc0:aaaa SC16G 14.8 GiB (quirks 0x00004000) [ 3.648754] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 3.658634] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 3.673806] devtmpfs: mounted [ 3.687910] Freeing unused kernel image (initmem) memory: 2048K [ 3.694160] Run /sbin/init as init process [ 3.698289] with arguments: [ 3.698302] /sbin/init [ 3.698315] with environment: [ 3.698327] HOME=/ [ 3.698340] TERM=linux [ 3.825026] usb 1-1.1: new high-speed USB device number 3 using xhci-hcd [ 3.966530] usb 1-1.1: New USB device found, idVendor=2c7c, idProduct=0800, bcdDevice= 4.14 [ 3.974964] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.982308] usb 1-1.1: Product: RM502Q-AE [ 3.986358] usb 1-1.1: Manufacturer: Quectel [ 3.990648] usb 1-1.1: SerialNumber: 54b42f53 [ 4.036055] systemd[1]: System time before build time, advancing clock. [ 4.245766] NET: Registered PF_INET6 protocol family [ 4.252419] Segment Routing with IPv6 [ 4.256181] In-situ OAM (IOAM) with IPv6 [ 4.264970] usb 1-1.3: new high-speed USB device number 4 using xhci-hcd [ 4.333429] systemd[1]: systemd 247.3-7+rpi1+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 4.357828] systemd[1]: Detected architecture arm. [ 4.372325] systemd[1]: Set hostname to . [ 4.406014] usb 1-1.3: New USB device found, idVendor=0424, idProduct=2740, bcdDevice= 2.00 [ 4.414418] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.421807] usb 1-1.3: Product: Hub Controller [ 4.426299] usb 1-1.3: Manufacturer: Microchip Tech [ 4.577812] uart-pl011 fe201000.serial: no DMA platform data [ 5.292240] systemd[1]: Queued start job for default target Multi-User System. [ 5.307425] systemd[1]: Created slice system-getty.slice. [ 5.314585] systemd[1]: Created slice system-modprobe.slice. [ 5.321729] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 5.329450] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ 5.336963] systemd[1]: Created slice User and Session Slice. [ 5.343480] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 5.352208] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 5.361226] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 5.371322] systemd[1]: Reached target Local Encrypted Volumes. [ 5.378070] systemd[1]: Reached target Paths. [ 5.382904] systemd[1]: Reached target Slices. [ 5.387939] systemd[1]: Reached target Swap. [ 5.398713] systemd[1]: Listening on Syslog Socket. [ 5.404798] systemd[1]: Listening on fsck to fsckd communication Socket. [ 5.412278] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 5.420290] systemd[1]: Listening on Journal Audit Socket. [ 5.426970] systemd[1]: Listening on Journal Socket (/dev/log). [ 5.434140] systemd[1]: Listening on Journal Socket. [ 5.450182] systemd[1]: Listening on udev Control Socket. [ 5.457005] systemd[1]: Listening on udev Kernel Socket. [ 5.463535] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 5.477226] systemd[1]: Mounting POSIX Message Queue File System... [ 5.489419] systemd[1]: Mounting RPC Pipe File System... [ 5.500935] systemd[1]: Mounting Kernel Debug File System... [ 5.512875] systemd[1]: Mounting Kernel Trace File System... [ 5.519425] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped. [ 5.538408] systemd[1]: Starting Restore / save the current clock... [ 5.551304] systemd[1]: Starting Set the console keyboard layout... [ 5.565015] systemd[1]: Starting Create list of static device nodes for the current kernel... [ 5.580380] systemd[1]: Starting Load Kernel Module configfs... [ 5.596192] systemd[1]: Starting Load Kernel Module drm... [ 5.609227] systemd[1]: Starting Load Kernel Module fuse... [ 5.619161] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 5.634508] systemd[1]: Starting File System Check on Root Device... [ 5.657399] systemd[1]: Starting Journal Service... [ 5.673647] fuse: init (API version 7.34) [ 5.686711] systemd[1]: Starting Load Kernel Modules... [ 5.703276] systemd[1]: Starting Coldplug All udev Devices... [ 5.728849] systemd[1]: Mounted POSIX Message Queue File System. [ 5.749233] systemd[1]: Mounted RPC Pipe File System. [ 5.760636] systemd[1]: Mounted Kernel Debug File System. [ 5.767416] systemd[1]: Mounted Kernel Trace File System. [ 5.777120] systemd[1]: Finished Restore / save the current clock. [ 5.787085] systemd[1]: Finished Create list of static device nodes for the current kernel. [ 5.800186] systemd[1]: modprobe@configfs.service: Succeeded. [ 5.808136] systemd[1]: Finished Load Kernel Module configfs. [ 5.818871] systemd[1]: modprobe@drm.service: Succeeded. [ 5.825788] systemd[1]: Finished Load Kernel Module drm. [ 5.833291] systemd[1]: modprobe@fuse.service: Succeeded. [ 5.840212] systemd[1]: Finished Load Kernel Module fuse. [ 5.848207] systemd[1]: Finished Load Kernel Modules. [ 5.861124] systemd[1]: Mounting FUSE Control File System... [ 5.887073] systemd[1]: Mounting Kernel Configuration File System... [ 5.907456] systemd[1]: Started File System Check Daemon to report status. [ 5.921288] systemd[1]: Starting Apply Kernel Variables... [ 5.934255] systemd[1]: Mounted FUSE Control File System. [ 5.945474] systemd[1]: Mounted Kernel Configuration File System. [ 5.969647] systemd[1]: Finished File System Check on Root Device. [ 6.001404] systemd[1]: Starting Remount Root and Kernel File Systems... [ 6.020887] systemd[1]: Started Journal Service. [ 6.178510] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null). Quota mode: none. [ 6.251819] systemd-journald[152]: Received client request to flush runtime journal. [ 6.264770] systemd-journald[152]: File /var/log/journal/3f826a13895241fbb0f4acc8b7a27b5d/system.journal corrupted or uncleanly shut down, renaming and replacing. [ 7.304052] mc: Linux media interface: v0.10 [ 7.372658] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned. [ 7.374864] bcm2835_vc_sm_cma_probe: Videocore shared memory driver [ 7.374894] [vc_sm_connected_init]: start [ 7.461462] videodev: Linux video capture interface: v2.00 [ 7.510223] [vc_sm_connected_init]: installed successfully [ 7.553449] brcmstb-i2c fef04500.i2c: @97500hz registered in polling mode [ 7.554129] brcmstb-i2c fef09500.i2c: @97500hz registered in polling mode [ 7.742399] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned. [ 7.747030] bcm2835_audio bcm2835_audio: there is not valid maps for state default [ 7.752611] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned. [ 7.800763] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned. [ 7.826191] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned. [ 7.888807] rpivid_hevc: module is from the staging directory, the quality is unknown, you have been warned. [ 7.893004] bcm2835-codec bcm2835-codec: Device registered as /dev/video10 [ 7.893105] bcm2835-codec bcm2835-codec: Loaded V4L2 decode [ 7.897174] bcm2835-codec bcm2835-codec: Device registered as /dev/video11 [ 7.897222] bcm2835-codec bcm2835-codec: Loaded V4L2 encode [ 7.918857] bcm2835_isp: module is from the staging directory, the quality is unknown, you have been warned. [ 7.956628] [drm] Initialized v3d 1.0.0 20180419 for fec00000.v3d on minor 0 [ 7.963936] rpivid feb10000.codec: Device registered as /dev/video19 [ 8.456197] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 8.502844] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 8.518878] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 8.523604] usbcore: registered new interface driver usbserial_generic [ 8.523686] usbserial: USB Serial support registered for generic [ 8.548830] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video13 [ 8.549702] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video14 [ 8.550164] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video15 [ 8.550598] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video16 [ 8.550633] bcm2835-isp bcm2835-isp: Register output node 0 with media controller [ 8.550659] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller [ 8.550682] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller [ 8.550704] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller [ 8.556147] bcm2835-codec bcm2835-codec: Device registered as /dev/video12 [ 8.556302] bcm2835-codec bcm2835-codec: Loaded V4L2 isp [ 8.561929] usbcore: registered new interface driver cdc_wdm [ 8.566689] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video20 [ 8.566889] bcm2835-codec bcm2835-codec: Device registered as /dev/video18 [ 8.566959] bcm2835-codec bcm2835-codec: Loaded V4L2 image_fx [ 8.569030] usbcore: registered new interface driver option [ 8.569138] usbserial: USB Serial support registered for GSM modem (1-port) [ 8.569530] option 1-1.1:1.0: GSM modem (1-port) converter detected [ 8.570083] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video21 [ 8.570556] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB0 [ 8.570712] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video22 [ 8.572552] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video23 [ 8.572628] bcm2835-isp bcm2835-isp: Register output node 0 with media controller [ 8.572656] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller [ 8.572678] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller [ 8.572700] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller [ 8.572988] bcm2835-isp bcm2835-isp: Loaded V4L2 bcm2835-isp [ 8.573625] bcm2835-codec bcm2835-codec: Device registered as /dev/video31 [ 8.573685] bcm2835-codec bcm2835-codec: Loaded V4L2 encode_image [ 8.623723] option 1-1.1:1.2: GSM modem (1-port) converter detected [ 8.681720] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB1 [ 8.708448] option 1-1.1:1.3: GSM modem (1-port) converter detected [ 8.709432] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB2 [ 8.825752] qmi_wwan 1-1.1:1.4: cdc-wdm0: USB WDM device [ 8.829897] qmi_wwan 1-1.1:1.4 wwan0: register 'qmi_wwan' at usb-fe9c0000.xhci-1.1, WWAN/QMI device, ca:77:3a:73:b6:f7 [ 8.830204] usbcore: registered new interface driver qmi_wwan [ 8.971983] brcmfmac: F1 signature read @0x18000000=0x15264345 [ 8.988722] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 8.993084] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,4-compute-module.bin failed with error -2 [ 9.273164] usbcore: registered new interface driver brcmfmac [ 9.274101] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 9.274270] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 9.280523] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Nov 1 2021 00:37:25 version 7.45.241 (1a2f2fa CY) FWID 01-703fd60 [ 9.883229] vc4-drm gpu: bound fe400000.hvs (ops vc4_hvs_ops [vc4]) [ 9.896263] Registered IR keymap rc-cec [ 9.896493] rc rc0: vc4 as /devices/platform/soc/fef00700.hdmi/rc/rc0 [ 9.905898] input: vc4 as /devices/platform/soc/fef00700.hdmi/rc/rc0/input0 [ 9.945753] vc4-drm gpu: bound fef00700.hdmi (ops vc4_hdmi_ops [vc4]) [ 9.948936] Registered IR keymap rc-cec [ 9.949751] rc rc1: vc4 as /devices/platform/soc/fef05700.hdmi/rc/rc1 [ 9.950643] input: vc4 as /devices/platform/soc/fef05700.hdmi/rc/rc1/input1 [ 9.968379] vc4-drm gpu: bound fef05700.hdmi (ops vc4_hdmi_ops [vc4]) [ 9.969754] vc4-drm gpu: bound fe004000.txp (ops vc4_txp_ops [vc4]) [ 9.970328] vc4-drm gpu: bound fe206000.pixelvalve (ops vc4_crtc_ops [vc4]) [ 9.970759] vc4-drm gpu: bound fe207000.pixelvalve (ops vc4_crtc_ops [vc4]) [ 9.971228] vc4-drm gpu: bound fe20a000.pixelvalve (ops vc4_crtc_ops [vc4]) [ 9.971620] vc4-drm gpu: bound fe216000.pixelvalve (ops vc4_crtc_ops [vc4]) [ 9.972075] vc4-drm gpu: bound fec12000.pixelvalve (ops vc4_crtc_ops [vc4]) [ 9.984450] [drm] No displays found. Consider forcing hotplug if HDMI is attached [ 9.984484] vc4-drm gpu: bound fe600000.firmwarekms (ops vc4_fkms_ops [vc4]) [ 9.990204] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS [ 10.001888] [drm] Initialized vc4 0.0.0 20140616 for gpu on minor 1 [ 10.005206] vc4-drm gpu: [drm] Cannot find any crtc or sizes [ 10.239145] 8021q: 802.1Q VLAN Support v1.8 [ 10.496696] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled [ 10.778496] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay) [ 10.780147] bcmgenet fd580000.ethernet eth0: Link is Down [ 15.814981] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 17.244076] ICMPv6: process `dhcpcd' is using deprecated sysctl (syscall) net.ipv6.neigh.wlan0.retrans_time - use net.ipv6.neigh.wlan0.retrans_time_ms instead [ 20.315130] vc4-drm gpu: [drm] Cannot find any crtc or sizes [ 33.754978] cam-dummy-reg: disabling [ 38.481188] tun: Universal TUN/TAP device driver, 1.6